Hallo

Nachdem über eine Woche das ISP gut funktionierte (mysmartusb, avrdude (v2.0) und AVR8 burn-o-mat(v1.4.2b) unter w2k im Attiny-Testplatinchen), kann ich inzwischen drei meiner ATtiny13 nicht mehr ansprechen:

Code:
C:\WinAVR\bin\avrdude.exe -q -u -C C:\WinAVR\bin\avrdude.conf -p t13 -P com2 -c AVR910 -E noreset,novcc  -U flash:w:C:\attiny\projekte\attiny.hex:a 
avrdude.exe: WARNING: -E option not supported by this Programmer type

Found programmer: Id = "AVR ISP"; type = S
    Software Version = 2.3; Hardware Version = 2.0
Programmer supports auto addr increment.

Programmer supports the following devices:
    Device code: 0x1c = ATtiny11
    Device code: 0x55 = ATtiny12
    Device code: 0x01 = ATtiny13
    Device code: 0x56 = ATtiny15
    Device code: 0x13 = AT90S1200
    Device code: 0x28 = AT90S4414
    Device code: 0x20 = AT90S2313
    Device code: 0x4c = AT90S2343
    Device code: 0x30 = AT90S4433
    Device code: 0x6c = AT90S4434
    Device code: 0x38 = AT90S8515
    Device code: 0x68 = AT90S8535
    Device code: 0x41 = ATMEGA103
    Device code: 0x46 = ATMEGA64
    Device code: 0x44 = ATMEGA128
    Device code: 0x03 = AT90CAN128
    Device code: 0x75 = ATMEGA16
    Device code: 0x74 = ATMEGA644
    Device code: 0x63 = ATMEGA162
    Device code: 0x64 = ATMEGA163
    Device code: 0x79 = ATMEGA169
    Device code: 0x14 = ATMEGA329
    Device code: 0x15 = ATMEGA3290
    Device code: 0x16 = ATMEGA649
    Device code: 0x17 = ATMEGA6490
    Device code: 0x72 = ATMEGA32
    Device code: 0x60 = ATMEGA161
    Device code: 0x76 = ATMEGA8
    Device code: 0x77 = ATMEGA8
    Device code: 0x3b = ATMEGA8515
    Device code: 0x6a = ATMEGA8535
    Device code: 0x5e = ATTINY26
    Device code: 0x29 = ATTINY261
    Device code: 0x2a = ATTINY461
    Device code: 0x2b = ATTINY861
    Device code: 0x06 = ATMEGA48
    Device code: 0x07 = ATMEGA88
    Device code: 0x08 = ATMEGA168
    Device code: 0x21 = ATtiny2313
    Device code: 0x09 = AT90PWM2
    Device code: 0x0a = AT90PWM3
    Device code: 0x22 = ATtiny25
    Device code: 0x23 = ATtiny45
    Device code: 0x24 = ATtiny85
    Device code: 0x0b = ATMEGA640
    Device code: 0x0c = ATMEGA1280
    Device code: 0x0d = ATMEGA1281
    Device code: 0x18 = ATMEGA2560
    Device code: 0x19 = ATMEGA2561
    Device code: 0x25 = ATtiny24
    Device code: 0x26 = ATtiny44
    Device code: 0x27 = ATtiny84
    Device code: 0x1a = AT90USB1286
    Device code: 0x1b = AT90USB1287
    Device code: 0x4b = ATMEGA325
    Device code: 0x4d = ATMEGA645
    Device code: 0x4e = ATMEGA3250
    Device code: 0x4f = ATMEGA6450

avrdude.exe: AVR device initialized and ready to accept instructions
avrdude.exe: Device signature = 0x000000
avrdude.exe: Yikes!  Invalid device signature.
             Double check connections and try again, or use -F to override
             this check.


avrdude.exe done.  Thank you.
Obwohl ich immer brav ausschalte beim Umstöpseln, alle externen Anschlüsse trenne, die Versorgungsspannung wie immer ist und der Reset-Impuls am Pin1 gemessen werden kann, reagieren die uCs nicht mehr.

Mache ich einen grundsätzlichen Fehler oder sterben die generell leicht? Oder ist meine Versorgungsspannung zu hoch (fast 5,5v bei frisch geladenen NIMH-Mignons).

Bisher habe ich nur flash- und eeprom-Daten übertragen und die fuses nicht verändert. Fummelt vielleicht avrdude an den fuses ohne das ich es will? Wie kann ich feststellen, was mit dem tiny nicht stimmt? Bei unverändertem Aufbau kann ich nach dem Tausch des defekten uCs sofort wieder flashen.

Ich hoffe, ihr könnt mir einen Tipp geben. Im Web finde ich nur Probleme und Lösungen beim Einrichten von ISP beschrieben. Hinweise auf unerklärlich "Zerschosse"(kein fuses-Fummeln, keine nicht funktionierende Betaktungen u.ä.), wie es bei mir der Fall ist, habe ich bisher noch nicht gefunden.

Gruß

mic

[Edit]Rechtschreibung im Titel korrigiert[/Edit]