Hartl
08.06.2008, 19:53
Hallo zusammen,
ich möchte mir eine Tankanzeige für das Motorrad Basteln, bleibe aber am Programm hängen, das ich nicht zum laufen bekomme. Was habe ich falsch gemacht (Neuling).
Ich bitte um euere Hilfe.
$regfile = "m8def.dat" ' ATmega8
$crystal = 3686400 ' myAVR Board
$baud = 4800
$hwstack = 60
$swstack = 60
$framesize = 60
'$sim
Config Lcd = 16 * 2
Config Lcdpin = Pin , Db4 = Portc.2 , Db5 = Portc.3 , Db6 = Portc.4 , Db7 = Portc.5 , E = Portc.1 , Rs = Portc.0
Config Timer1 = Counter , Edge = Falling
Config Pind.5 = Input
Set Portd.5
On Timer1 Timer1_isr
Dim Count0 As Word
Dim Count1 As Word
Dim Count2 As Single
Dim Count3 As Single
Dim Verbr As String * 5
Dim Inh As String * 5
Cls
Cursor Off Noblink
Enable Timer1
Enable Interrupts
'---------------------------------------------------------
Do
Count1 = 45120 - Count0
Count2 = Count1 / 1880 'Geber 1880 Impulse/L
Inh = Fusing(count2 , "#.##")
Count3 = Count0 / 1880
Verbr = Fusing(count3 , "#.##")
If Count2 > 10 Then
Locate 1 , 1
Lcd "Inhalt: " ; Inh ; " L"
Else
Locate 1 , 1
Lcd "Inhalt: " ; Inh ; " L"
End If
If Count3 > 10 Then
Locate 2 , 1
Lcd "Verbr.: " ; Verbr ; " L"
Else
Locate 2 , 1
Lcd "Verbr.: " ; Verbr ; " L"
End If
Waitms 500
Loop
End
'---------------------------------------------------------
Timer1_isr:
Incr Count0
Return
'---------------------------------------------------------
Vielen Dank im Voraus
Gruß
Gerhard
ich möchte mir eine Tankanzeige für das Motorrad Basteln, bleibe aber am Programm hängen, das ich nicht zum laufen bekomme. Was habe ich falsch gemacht (Neuling).
Ich bitte um euere Hilfe.
$regfile = "m8def.dat" ' ATmega8
$crystal = 3686400 ' myAVR Board
$baud = 4800
$hwstack = 60
$swstack = 60
$framesize = 60
'$sim
Config Lcd = 16 * 2
Config Lcdpin = Pin , Db4 = Portc.2 , Db5 = Portc.3 , Db6 = Portc.4 , Db7 = Portc.5 , E = Portc.1 , Rs = Portc.0
Config Timer1 = Counter , Edge = Falling
Config Pind.5 = Input
Set Portd.5
On Timer1 Timer1_isr
Dim Count0 As Word
Dim Count1 As Word
Dim Count2 As Single
Dim Count3 As Single
Dim Verbr As String * 5
Dim Inh As String * 5
Cls
Cursor Off Noblink
Enable Timer1
Enable Interrupts
'---------------------------------------------------------
Do
Count1 = 45120 - Count0
Count2 = Count1 / 1880 'Geber 1880 Impulse/L
Inh = Fusing(count2 , "#.##")
Count3 = Count0 / 1880
Verbr = Fusing(count3 , "#.##")
If Count2 > 10 Then
Locate 1 , 1
Lcd "Inhalt: " ; Inh ; " L"
Else
Locate 1 , 1
Lcd "Inhalt: " ; Inh ; " L"
End If
If Count3 > 10 Then
Locate 2 , 1
Lcd "Verbr.: " ; Verbr ; " L"
Else
Locate 2 , 1
Lcd "Verbr.: " ; Verbr ; " L"
End If
Waitms 500
Loop
End
'---------------------------------------------------------
Timer1_isr:
Incr Count0
Return
'---------------------------------------------------------
Vielen Dank im Voraus
Gruß
Gerhard